View LV10003_1268494.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Voltage Transducer LV 100
For the electronic measurement of voltages : DC, AC, pulsed..., with a galvanic isolation between the primary circuit (high voltage) and the secondary circuit (electronic circuit).
IPN = 10 mA VPN = 100 .. 2500 V
Electrical data
IPN IP RM Primary nominal r.m.s. current Primary current, measuring range Measuring resistance with 15 V ISN KN VC IC Vd @ 10 mA @ 20 mA
max max
10 mA 0 .. 20 mA RM min RM max 0 0 150 50 mA V mA kV
Features
* Closed loop (compensated) voltage * Insulated plastic case recognized
according to UL 94-V0. transducer using the Hall effect
Secondary nominal r.m.s. current Conversion ratio Supply voltage ( 5 %) Current consumption R.m.s. voltage for AC isolation test 1), 50 Hz, 1 mn
50 10000 : 2000 15 10 + IS 6
Principle of use
* For voltage measurements, a current
proportional to the measured voltage must be passed through an external resistor R 1 which is selected by the user and installed in series with the primary circuit of the transducer.
Accuracy - Dynamic performance data
XG
L
Overall Accuracy @ IPN , TA = 25C Linearity Offset current @ IP = 0, TA = 25C Thermal drift of IO 0C .. + 70C Response time 2) @ 90 % of VPN
0.7 < 0.1 Typ Max 0.2 0.3
% % mA mA s
Advantages
* * * * * *
Excellent accuracy Very good linearity Low thermal drift Low response time High bandwidth High immunity to external interference * Low disturbance in common mode.
IO IOT tr
0.2
20 .. 100
General data
TA TS RP RS m Ambient operating temperature Ambient storage temperature Primary coil resistance @ TA = 70C Secondary coil resistance @ TA = 70C Mass Standards 0 .. + 70 - 25 .. + 85 1900 60 460 EN 50178 C C g
Applications
* AC variable speed drives and servo * Static converters for DC motor drives * Battery supplied applications * Uninterruptible Power Supplies * Power supplies for welding
applications. (UPS) motor drives
Notes :
1) 2)
Between primary and secondary R 1 = 100 k (L/R constant, produced by the resistance and inductance of the primary circuit). 030131/6
LEM Components
w w w .lem.com
Dimensions LV 100
(in mm. 1 mm = 0.0394 inch)
Front view
Left view
Connection
Top view Mechanical characteristics
* General tolerance * Transducer fastening
Fastening torque max * Connection of primary Fastening torque max * Connection of secondary 0.3 mm 2 holes 6.5 mm M6 steel screws 5 Nm or 3.69 Lb - Ft. M5 screw terminals 2.2 Nm or 1.62 Lb - Ft. Faston 6.3 x 0.8 mm
Remarks
* IS is positive when VP is applied on terminal +HT. * This is a standard model. For different versions (supply
voltages, turns ratios, unidirectional measurements...), please contact us.
Instructions for use of the voltage transducer model LV 100 Primary resistor R 1 : the transducer's optimum accuracy is obtained at the nominal primary current. As far as possible, R 1 should be calculated so that the nominal voltage to be measured corresponds to a primary current of 10 mA. Example: Voltage to be measured VPN = 1000 V a) R 1 = 100 k/40 W, IP = 10 mA b) R 1 = 400 k/ 5 W, IP = 2.5 mA Accuracy = 0.7 % of VPN (@ TA = +25C) Accuracy = 2.5 % of VPN (@ TA = +25C)
Operating range (recommended) : taking into account the resistance of the primary windings (which must remain low compared to R 1, in order to keep thermal deviation as low as possible) and the isolation, this transducer is suitable for measuring nominal voltages from 100 to 2500 V.
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice.

▲Up To Search▲

Price & Availability of LV10003

	To Download LV10003 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .